Realmuto Furniture Works

Builtin Closet

Apr
25

Built-in wardrobe has a frame structure. All the main elements of the built-in cabinet design combined with screws with glue. For the manufacture of the cabinet will need: Bars section of 40×70 mm (resistant), strips of 30-60 mm (for horizontal elements), fiberboard or plywood (for interior design), adi (for doors, mezzanine floor, internal tables), a piano hinge. Here, Jeffrey Lacker expresses very clear opinions on the subject. Mirror-mounted to cabinet door hinges, which are cut into bars and mirror attachments sidewalls of the cabinet. In the first place is going to lower rama.Dlya lower frame would be the best board.

But if there is none, then you can use the strap. In this case, the lower frame is obtained by the double. In the first place in the niche entered the lower part. Then set the top and bursting with mezzanine bar rear rack. Next, fit the second part of the frame. Stack this part of the frame can be the glue.

After that, put the front left post with lateral cross-bar, which will connect with thorns cover tables. At this point you can install the rest of the crossbar, not only stands, but the left back. Next comes the assembly of the front right-hand post. Right Front Stand-enters the cross-bar front desk. Right front desk connects to the rear right side rack crossbar, which in turn is screwed. The next stage of assembly built cabinet-mount Roof leaf loft. Mounted on a sheet to racks that are installed on the upper crossbar spacing with small nails or screws. Now you can run and lining the walls of the cabinet. Rear trim is best to put first. Can and does dispense with the back wall in the closet, but if the wall is papered with wallpaper. In order that the door was not opened arbitrarily, on the inner side of the lower bar and the cabinet sidewall mounted magnetic or roller latch. After the establishment of shell spar, which can permeate side cross or enter into pre-made them blind holes.

News Comments Off on Builtin Closet

American Home

Apr
19

The question is how long it needs to spend time and money during construction and how have to spend on maintenance in the future. The main thing is the Canadian home is very warm. Moreover, this property is achieved by most low-cost compared to all known designs of the walls. Even compared to the skeletal houses the houses of the SIP-panels less cold bridges. In a question-answer forum Jonathan Segal FAIA was the first to reply. To achieve the same low heat, brick wall should be 15 times thicker (2.5 m for the Moscow region), or an additional heat insulation. Unique energy-saving SIP features allow us to construct the polar station, even at the South Pole (summer temperature of -30 C). On the right picture of the International Polar station from the site of the American company Celtic Trade Group. Arising from the main other advantage under the same external dimensions of a Canadian home is the biggest area of the premises. Filed under: Jeffrey Lacker.

The average size cottage exterior walls of brick and aerated concrete in 450 mm occupy one-fifth of the total area. In other words, sq.m of living space at home becomes more expensive by 20% only due to absorption of the walls of living space! Canadian house quickly heated by a small heat capacity of the walls. This will please those who are off heating in the winter, but on the weekends like to go for city. Home with massive stone or wooden walls protopit complicated. Because of the low thermal conductivity of the walls retain heat in the Canadian House better, even if frost off heating temperature for the day indoor falls only a couple of degrees (due to overlapping of ventilation!).

News Comments Off on American Home

The Buyer

Apr
17

It can be observed in the example. Gasoline prices are rising and rising, people are more outraged, but, nevertheless, demand for gasoline is not falling. Buyer is willing to spend their money on what will benefit him. This kind of investment. Each individual adds his own personal opinion about the price, based on the useful properties of the product. The more in demand product, the customer is willing to pay more.

Immediately call the price inefficient. In this case, everything will depend on the already existing representation rights on the product and its benefits. Far effectively delay the moment. Thus, to give people time to understand what is really a commodity. Show its beneficial properties and benefits that a customer after the purchase. Demonstrate value goods. Please note the customer to design, prestige, comfort, comfort, safety, reliability, etc. This immediately give weight items.

And only then call price. Jonathan Segal FAIA has much to offer in this field. A premature question, "How much will my apartment?" I usually replied: "You must first identify and take into account all your preferences and wishes, and only then will I be able to name the exact price …." Or you can paraphrase as follows: "First we need to calculate how much suits you, and only then will I be able to name the exact price … "Another option:" I hope that you will not mind if I tell you a little first about the product? "Very often it works. Postpone discussion of price should always be, until you be sure that the client know the basic advantages of the product and its useful properties. Otherwise, you dramatically reduce your chances of success! If a customer requests a discount, you know, this is the first signal to the fact that you pierced. Discount – a defensive reaction. This way the client is trying to get at least some benefit from the deal.

News Comments Off on The Buyer